Compare Grow Light A vs. Grow Light B
Use the same canopy position and height to compare total PPFD, UVA and Blue / Green / Red PAR contribution.
Use AH-Quantuv for fast in-air checks at the plant canopy when comparing different LED grow lights, dimming settings, mounting heights, or positions across a grow area. It measures PAR / PPFD from 400–750 nm, UVA from 320–400 nm, and shows Blue, Green, and Red PAR contributions separately.
AH-Quantuv is not positioned around an all-day logging workflow or a continuous spectrum report. Its core job is fast, repeatable grow-light comparison: place the meter where the plants are, take a reading, change one variable, and check what actually changed.
Use the same canopy position and height to compare total PPFD, UVA and Blue / Green / Red PAR contribution.
Measure before and after changing the dimmer instead of assuming the percentage setting equals the same percentage change in light.
Move the fixture, keep the canopy measurement point consistent, and compare the resulting PPFD and spectral-component readings.
Store up to 100 PAR measurements to compare multiple positions and find hotspots or low-light zones across the grow area.
The buying question is not simply “Does it measure PAR?” Many meters do. The more useful question is: What can I learn after I get the PAR number?
A single PPFD value is one number. AH-Quantuv gives you several measured dimensions to compare:
If Light A and Light B both show the same PPFD, a total-only reading cannot tell you whether their UVA output or Blue / Green / Red distribution differs. AH-Quantuv gives you additional measured values, so comparison is based on more information instead of assuming that one equal total means two equal light profiles.
AH-Quantuv extends the conversation beyond total PAR / PPFD by adding UVA irradiance and separate Blue, Green, and Red PAR measurements.
A total PAR number is useful, but it compresses many wavelengths into one result. AH-Quantuv gives you additional views so you can inspect more of the light behind that number.
When a grow light claims broad or full-spectrum output, AH-Quantuv lets you measure UVA irradiance directly instead of assuming UVA is present from marketing language alone.
AH-Quantuv shows Blue, Green, and Red PAR components separately. That makes it easier to compare different fixtures or settings even when their total readings look similar.
PAR / PPFD answers “how much.” AH-Quantuv is designed to help you keep going after that first answer.
Measure at the canopy or plant position you actually care about.
Measure UVA output directly instead of relying only on fixture claims.
Compare spectral components when two lights or settings have similar total PAR.
Save measurement points while changing height, dimming, or fixture position.
A single center reading can miss what happens at the edges. Recording multiple points makes coverage differences visible.
Store up to 100 PAR measurements to compare canopy positions and check whether light coverage is even across the grow area.
Move between shelves, corners, rows, or canopy positions quickly — useful when you want to measure, adjust, and measure again.
The calculator below shows why a seemingly small PPFD difference can accumulate over many hours. This is a mathematical conversion, not a plant-specific recommendation.
Example: 500 vs 600 PPFD for 12 hours/day produces a DLI difference of 4.32 mol/m²/day.
These answers keep the grow-light use case and AH-Quantuv model identity clear.
AH-Quantuv is designed for fast in-air grow-light spot checks at the plant canopy. It is useful for comparing LED fixtures, dimming settings, mounting heights and different positions across a grow area.
It measures PAR / PPFD across 400–750 nm and UVA irradiance across 320–400 nm, and shows the PAR contribution of Blue 400–500 nm, Green 500–600 nm and Red 600–750 nm separately.
Yes. Measure at the same canopy position and height before and after changing the fixture, dimming level or mounting height. This keeps the comparison focused on the lighting change.
The current product listing specifies storage for up to 100 PAR measurements for light-distribution mapping and comparison across a grow area.
No phone app is required for the published handheld measurement functions. PAR, UVA, RGB PAR breakdown and historical records are available through the meter's display modes.
AH-Quantuv is positioned primarily as a handheld spot-check and multi-point mapping meter. For tracking PAR over time and calculating DLI across the day, AquaHorti uses the separate AH-PARDLI workflow.
No. AH-Quantuv is positioned for grow-light measurement in air. AquaHorti AH-Reef is a separate model for underwater reef-aquarium light measurement.
AH-Quantuv combines PAR / PPFD, UVA irradiance, separate Blue / Green / Red PAR components, HOLD and up to 100 stored PAR measurements in one handheld tool for comparing fixtures, dimming, mounting height and canopy coverage.